RIGID Industries SR-L Series Marine Flush Mount LED Spreader Pod

 

The RIGID Industries SR-L Series Marine Flush Mount LED Spreader Pod combines broad working light with a clean marine appearance for boats, docks, trailers, and utility areas exposed to demanding conditions. Its compact 4-inch form and white housing suit installations where nearby visibility matters as much as a finished look. The flush mount design supports a recessed, integrated appearance while keeping the light easy to place around decks, transoms, cabins, and loading areas.

An ultra-wide 120-degree spreader pattern is designed to illuminate the area around the mounting location instead of concentrating output far downrange. That broad coverage helps customers see walking areas, gear, tie-down points, storage areas, and nearby water with fewer harsh hot spots. The pattern is especially useful when maneuvering at low speed, preparing equipment before departure, or working around a vessel after dark.

The marine-grade construction uses an Alodine-treated housing, durable UV powder coat, corrosion-conscious mounting components, and a UV-protected polycarbonate lens. Integrated thermal management and a pressure-equalizing vent support consistent operation as temperatures and environmental conditions change. An IP68 rating adds protection against dust and water ingress, making the light well suited to fresh-water and salt-water recreation when installed with appropriate marine wiring practices.

High-power, low-power, and halo-backlighting-only modes give customers more control over how much light is used at a given moment. High power supports active work and loading, low power offers gentler area illumination, and the halo can provide a low-level accent without the full spreader output. High and low modes use a soft-start sequence that increases intensity over about four seconds, helping eyes adjust more comfortably around reflective water and bright decks.

The flush mount format fits into a prepared opening so the outer trim sits close to the mounting surface. Hidden mounting details and glossy outer trim contribute to a tidy appearance, while the white housing coordinates with many gelcoat, fiberglass, aluminum, and painted marine finishes. White and blue halo choices allow the accent lighting to complement a neutral lighting scheme or a cooler custom look without changing the primary white spreader beam.

Careful planning of the mounting location, wiring path, switch access, and beam direction helps the light serve as a practical part of the vessel rather than an added-on accessory. It can support dockside loading, deck cleanup, trailer preparation, equipment checks, and low-speed utility tasks where broad nearby illumination is preferred. Whether customers are upgrading for deck visibility, night loading, dockside work, or marine accent lighting, the RIGID Industries SR-L Series Marine Flush Mount LED Spreader Pod delivers controlled wide-area coverage with a corrosion-conscious white housing. Now Available at LEER!

 

---

 

Features & Specifications

Product Type: Marine LED spreader pod

Brand: RIGID Industries

Series: SR-L Series Marine

Vehicle Fitment: Universal marine and utility lighting

Light Size: 4-inch

Housing Color: White

Mount Type: Flush Mount

Beam Pattern: Ultra-wide 120-degree spreader

Halo Color Options: White or blue

Operating Modes: High power, low power, or halo backlighting only

Voltage Range: 9V-36V DC

Lens: UV-protected polycarbonate

Ingress Protection: IP68

Corrosion Protection: Alodine-treated housing with durable UV powder coat

Functionality:

• Illuminates broad deck, transom, dock, and loading areas at close range
• Supports high-power lighting for active work and low-power lighting for reduced glare
• Provides halo-only accent illumination when the full spreader beam is not needed
• Soft-start operation increases high and low output gradually over about four seconds
• Recessed mounting creates a low-profile finished appearance in a prepared surface
• White housing coordinates with many marine finishes and equipment enclosures
• Wide input voltage supports properly designed marine, trailer, and utility electrical systems

 

---

 

Available Options

The RIGID Industries SR-L Series Marine Flush Mount LED Spreader Pod is available with two halo accent colors:

• White Halo - Creates a clean neutral accent that coordinates with white deck lighting, cabin lighting, and understated marine finishes.
• Blue Halo - Adds a cooler custom accent for customers who want the light to complement blue courtesy lighting or vessel styling.

Choose the White Halo for a neutral integrated appearance, or choose the Blue Halo for a cooler custom accent around the primary white spreader beam.

 

---

 

Why Choose

This product is ideal for customers who want wide marine area lighting, flexible operating modes, and a clean recessed white-housing installation.

• Broad 120-degree coverage helps illuminate nearby work areas instead of concentrating light in one narrow spot
• High, low, and halo-only modes support different tasks and ambient-lighting needs
• Soft-start behavior helps eyes adjust around reflective water and bright decks
• Marine-focused corrosion protection supports demanding fresh-water and salt-water environments
• Flush mounting keeps the housing close to the surrounding panel for an integrated appearance
• IP68 protection and a UV-protected lens support outdoor exposure when installed correctly
• White and blue halo choices allow appearance to be matched to the vessel's lighting theme

 

---

 

What's Included

• One RIGID Industries SR-L Series Marine flush mount spreader light in a white housing
• Integrated white or blue halo backlighting, based on the selected version
• Flush-mount trim and installation hardware supplied with the light

Note: Confirm included components before installation.

 

---

 

Installation Notes

• Confirm the panel has adequate rear clearance, structural support, wiring access, and service space before cutting the flush-mount opening
• Use marine-grade wire, sealed connections, proper circuit protection, and corrosion-resistant installation practices
• Verify switch logic for high power, low power, and halo-only operation before completing final wiring
• Aim the spreader beam toward the intended deck or work area while limiting glare toward operators, passengers, and nearby vessels

Buyer is responsible for use in accordance with applicable vehicle, road, off-road, towing, racing, and local laws.

 

---

 

Warranty Information

RIGID LED lighting is backed by a limited lifetime warranty against defects in materials and workmanship, subject to the brand's published terms, exclusions, and claim procedures. Proof of purchase may be required, and warranty service may require review of the product and installation.

Coverage typically excludes improper installation, misuse, unauthorized modification, electrical faults outside the light, overvoltage, tampering, neglect, collision or impact damage, and use that falls outside the product's intended application. Mounts, accessories, finishes, and related components may carry different coverage periods, so customers should retain purchase records and review the applicable warranty terms before beginning a claim.